Working right across Western Australia|Breakdowns answered 24/7
Thermo Dynamic
Services

Design, installation, commissioning and service

Industrial energy work usually gets handed between a designer, a fitter, a certifier and a service contractor. We hold the whole scope, starting with a clear understanding of what you need and keeping quality the standard through to sign-off.

01

Burners & boilers

The core discipline. Whether the unit is new, twenty years old or a brand nobody stocks any more, we work out whether it should be tuned, rebuilt or replaced, and say so plainly.

New burner fitted to an existing sectional boiler, the unit it replaced on the floor alongsideRetrofit
Hot water boiler with a new burner, gas train and controls fittedRetrofit

Burner retrofits into existing plant. The old unit comes out, a modern controllable burner and gas train go on to the same chamber, and the whole thing is recommissioned.

Burner selection & sizing

Turndown, flame shape and control method matched to the chamber and the duty.

Retrofits & upgrades

Modern, controllable units into existing plant without a full rebuild.

Boiler plant

Steam and hot water generation: installation, service and efficiency work.

Controls & safety interlocks

Flame safeguard, purge and proving specified and set to standard.

02

Systems design

Before anything is quoted, the duty gets calculated. We work from your process: throughput, temperature and cycle times. The system gets designed to that, then plant, gas supply and controls are specified as one package.

Three dimensional model of a fan and drive assembly mounted to a plant casingAssembly
Sectioned view through the same drive showing shaft, bearings and pulleysSection

Plant is modelled and sectioned before anything is ordered, so clearances, drive geometry and bearing arrangement are resolved on screen rather than on site.

Heat load & duty calculation

Sized against the real process, not the old nameplate.

Plant layout

Access, flue routing, ventilation and clearances resolved on paper first.

Fuel & energy strategy

What the plant will cost to run, and the options that change that number.

Drawings & specification

Schedules and P&IDs you can put out to tender if you'd rather.

03

Gas lines & technical submissions

Gas lines, trains and appliance connections installed by licensed fitters. The technical submission is prepared and lodged by the same people who designed the job.

Gas train and ribbon burner set up on a test stand with a digital manometer

Gas train built up and proved on a ribbon burner: regulator, safety shut off valves, modulating control and pressure test points, with operating pressures recorded.

A
Technical submissions

Prepared and lodged.

B
Gas lines & reticulation

From the meter, sized for current and future load.

C
Gas trains & valve sets

Regulators, filters, proving systems and vent lines, pressure tested and tagged.

D
Compliance certificates

Issued at completion.

E
Shutdown works

Scoped and staged around your shutdown window.

04

Commissioning & decommissioning

Lighting reliably and running efficiently are two different things. We set air-fuel ratio across the firing range, verify turndown and interlocks, and hand you the numbers. Plant coming out is isolated, purged and made safe with the same rigour.

Engineer alongside an industrial burner

Commissioning is done by our own licensed people, on site, with the readings recorded as they are taken.

Packaged steam boiler with water treatment and feed skid during installationNew plant
Packaged steam boiler and feed system after commissioningCommissioned

Steam plant taken from installation through to commissioning: feedwater and treatment set up, burner tuned across the firing range, safeties proved and the readings handed over.

Example commissioning record
Flue O₂
3.5 %
CO
<50 ppm
Combustion efficiency
83.5 %
Turndown achieved
5:1
Gas rate at high fire
1,150 MJ/h
Safety shutdown time
1.0 s

Indicative industry figures shown. Every job is handed over with its own recorded sheet.

05

Fault finding, repairs & maintenance

Intermittent lockouts, uneven cure, gas bills that crept up. These are the faults that get lived with because nobody could pin them down. We diagnose first and quote second, and where plant matters we put it on a scheduled agreement so the failures stop being a surprise.

Combustion chamber with failed insulation and heavy scaling around the burner openingBefore
The same chamber relined and repanelled around the burner openingAfter

Combustion chamber found with failed lining and scaling around the burner opening, stripped back and relined.

Corroded flanged connection revealed under failed lagging, with rust debris below Found
New flanged connection with a fresh weld and new fasteners in place Repaired

Corrosion found under the lagging on a vessel connection during a service visit. Joint cut out, new flanged spool welded in and pressure tested.

Cracked burner side wall with flame escaping through the crackBefore
The same burner side wall after repairAfter

During an annual burner service the burner side wall was found to be cracked, allowing unburned gas to escape. The burner was repaired.

Service agreement
Fixed annual scope

Scheduled inspections, tuning and certificate renewal, priced for the year so it can be budgeted rather than met as it arises.

Planned service visits booked a year in advance, annually as a minimum, so plant is attended before it fails
Full burner service: head, electrodes, ignition, flame sensing, injectors, filters, fan and air controls stripped, cleaned and inspected
Combustion tuning with a calibrated flue gas analyser, readings recorded before and after across the firing range
Gas train and reticulation checks: valves, regulators, filters, operating pressures and a leak test
Safety and shutdown testing: flame failure timing, gas and air pressure proving, high limit and water level protection, lockout function
Compliance documentation to industry standard, issued for every appliance covered
A written report after each visit with results, photographs and anything found, priced so it can go straight to budget
Priority breakdown response, 24/7, at agreed rates
An asset register of the plant covered, with full service history held on file

Not included: parts and major components, refractory and pressure vessel work, rectification of pre-existing defects, and anything outside the agreed scope. All quoted before work starts.

Breakdown callout

Fault-find, make safe, and a straight answer on repair versus replace.

· Breakdowns 24/7· Metro, regional and remote WA· Site report with findings issued after attendance, then a plan agreed with you
06

Engineering the future of industrial energy

Our R&D arm. We keep developing better ways to run the plant we work on, and products of our own where nothing on the market does the job properly. Changes are trialled on one line before going wider.

Better process

Where the heat and the cycle time are actually going, measured on your plant.

Products of our own

Developed in-house where the market has no answer. Detail shared directly, under agreement.

Efficiency retrofits

Recovery, insulation and control strategy, measured before and after.

Alternative methods

Other ways to get the heat you need, assessed against your own numbers rather than a brochure.

Process

From assessment to handover

01
Site assessment

We come and look at the plant.

02
Scope & price

Itemised scope, inclusions, exclusions and a program.

03
Approve, install, commission

Submission lodged, works executed to the agreed window, daily contact on site.

04
Handover pack

Certificates, commissioning data, as-builts and O&M documentation.